2006 Toyota Corolla recalls and problems

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been n…

The Agency received a petition on September 11, 2014 requesting an investigation into, low-speed surging in the 2006-2010 Toyota Corolla [vehicles] with ETCS-i, in which the brakes fail to stop the vehicle in time to prevent a crash.NHTSA conducted a technical review of the material cited and provided by the petitioner, material Toyota submitted in response to a NHTSA formal request, interviews with complainants and manufacturer representatives, as well as the results of testing of the complaint vehicle.Taking into account the allocation of agency resources, agency priorities, and the likelihood that an additional investigation would result in a finding that a defect related to motor vehicle safety exists, NHTSA has concluded that further investigation of the issues raised by the petition is not warranted.The agency accordingly has denied the petition.The official petition denial, as published in the Federal Register, is available in the document file for this defect petition, as well as copies of reference material related to the denial.Regarding the VOQs associated with the closing of this investigation, the scope as defined by the petitioner is MY 2006 through 2010 Toyota Corollas.Of the 163 VOQs submitted by the petitioner, 149 are within that specific population (11 of the 163 were outside the model and model year scope of investigation as defined by the petitioner and 3 VOQs were submitted by owners from foreign countries) and 6 of the 163 are duplicate submissions.Ther…

On August 26, 2010, Toyota submitted a Defect Information Report to the National Highway Traffic Safety Administration (NHTSA) regarding problems with Engine Control Modules that could result in engine stall while driving in certain model year (MY) 2005 through 2008 Toyota Corolla, Corolla Matrix and Pontiac Vibe vehicles equipped with the 1ZZ-FE engine and two-wheel drive and manufactured between April 19, 2004 and January 2, 2008.Toyota's report indicated that cracks may develop at certain solder point or on varistors on the ECMs.According to Toyota, such cracks generally resulted in engine warning lamp illumination, harsh shifting or engine no-start.In some cases, if the cracking occurs on particular solder points or varistors, the engine could stop while the vehicle is being driven.Toyota will notify owners of subject vehicles that they should return their vehicles to a Toyota or Pontiac dealer.Dealers will be instructed to inspect the production number of the ECM for each vehicle and replace the ECM if necessary.On November 30, 2009, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE09-054) to investigate alleged engine stall while driving in model year (MY) 2006 Toyota Corolla and Corolla Matrix vehicles.In its response to ODI's information request, submitted on March 2, 2010, Toyota indicated that it had identified two possible conditions with ECMs used in MY 2005 through 2007 Toyota Corolla and Matrix vehicles:1) cracks forming between the I…

On November 30, 2009, the Office of Defects Investigation (ODI) opened a preliminary evaluation (PE09-054) to investigate alleged engine stalling, while driving in model year (MY) 2006 Toyota Corolla and Corolla Matrix vehicles .In its response to ODI's information request submitted on March 2, 2010, Toyota indicated that it had identified two possible causes of production defects of the engine control units (ECU) used in the MY 2005 through 2007 Corolla and Matrix vehicles equipped with the 1ZZ-FE engine.Failure mode A1 - BGA ball failure caused by improperly cured conformal coating applied to ECU circuit boards. This can cause cracks to form in the soldered joints of some components. Failure mode A2 - Varistor over heating; a glass coating is created on the surface of the Varistor during its production process.In case of an insufficient coating, a crack can occur in the surface of the glass coating. When ions are charged in the plating electrolytes after the glass coating process, the plating electrolytes can penetrate into the Varistor through the glass crack then an electrical short occurs. With respect to these failures, if the condition arises, it can potentially lead to one or more of the following: MIL on, engine stall or engine no start, harsh shifting.Of the approximately 155,000 warranty and extended warranty claims Toyota has analyzedthe projected 5 year failure rate of the ECU associated with an engine stall is 0.8%. This investigation has been upgraded to an Eng…