2010 Peterbilt 386 recalls and problems

The 2010 Peterbilt 386 has 5 recalls and 1 owner complaint on file with NHTSA; the most reported problem area is visibility.

How the 2010 compares

Low

Fewest complaintsMost complaints

Low complaint count among 8 386 model years — 6th most.

5recalls

1complaints

0crashes

0fires

0injuries

—median miles

Owner complaints filed with NHTSA, not verified and not adjusted for sales. Ranking compares this model's own years only.

Does your car have an open recall?
Recalls apply to specific vehicles. Only a VIN lookup on NHTSA's official site shows whether yours is affected and still unrepaired.

Check your VIN →

5 recalls

Electronic Stability Control

Apr 6, 2020 · NHTSA campaign 20V199000 · 460,515 vehicles

Problem: PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Remedy & notes

PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Equipment

Nov 25, 2013 · NHTSA campaign 13V593000 · 561 vehicles

Problem: Paccar Incorporated (Paccar) is recalling certain 2004-2013 Peterbilt 379, 357, 378, 367, 388, 365, 389, 385 and 386 trucks manufactured from April 3, 2003, through October 25, 2013 and equipped with tri-drive rear axles and a tag or pusher axle. The affected vehicles may be missing required information from the certification label, specifically the tag or pusher axle the gross axle weight rating, suitable tire and rim information, and recommended tire pressure information. Without this information, the vehicles do not comply with the requirements of 49 C.F.R. Part 567, "Certification."

Risk: As a result, the axles may be overloaded or the wrong tires could be installed or the tires could be improperly inflated. All of these issues increase the risk of a crash.

Remedy & notes

Peterbilt will notify owners and dealers will inspect and replace the certification labels missing the necessary information. The recall is expected to begin in January 2014. Customers can contact Peterbilt at 1-940-591-4000. Peterbilt's number for this campaign is 1113-F.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Electrical System

Jul 21, 2011 · NHTSA campaign 11V380000 · 211 vehicles

Problem: Paccar is recalling certain model year 2011-2012 Kenworth T660, T700, and T800 vehicles manufactured from April 19, 2010, through May 13, 2011, and model year 2008, 2010, and 2011 Peterbilt 365, 367, 384, 386, 387, 388 and 587 vehicles manufactured from April 20, 2010, through June 11, 2011, and equipped with paccar mx engines and eaton ultrashift dm or allison automatic transmissions (without auto-neutral). The fast idle control May be activated by the operator while the transmission is in gear.

Original NHTSA wording

PACCAR IS RECALLING CERTAIN MODEL YEAR 2011-2012 KENWORTH T660, T700, AND T800 VEHICLES MANUFACTURED FROM APRIL 19, 2010, THROUGH MAY 13, 2011, AND MODEL YEAR 2008, 2010, AND 2011 PETERBILT 365, 367, 384, 386, 387, 388 AND 587 VEHICLES MANUFACTURED FROM APRIL 20, 2010, THROUGH JUNE 11, 2011, AND EQUIPPED WITH PACCAR MX ENGINES AND EATON ULTRASHIFT DM OR ALLISON AUTOMATIC TRANSMISSIONS (WITHOUT AUTO-NEUTRAL). THE FAST IDLE CONTROL MAY BE ACTIVATED BY THE OPERATOR WHILE THE TRANSMISSION IS IN GEAR.

Risk: If the fast idle control function is engaged with the transmission in gear, the vehicle could unexpectedly accelerate and override the parking brake and , creating a risk of a crash and damage to other vehicles or property and the potential for injury to nearby pedestrians.

Original NHTSA wording

IF THE FAST IDLE CONTROL FUNCTION IS ENGAGED WITH THE TRANSMISSION IN GEAR, THE VEHICLE COULD UNEXPECTEDLY ACCELERATE AND OVERRIDE THE PARKING BRAKE AND , CREATING A RISK OF A CRASH AND DAMAGE TO OTHER VEHICLES OR PROPERTY AND THE POTENTIAL FOR INJURY TO NEARBY PEDESTRIANS.

Remedy & notes

Kenworth and Peterbilt dealers will update the engine software for the affected chassis. This service will be performed free of charge. The safety recall began on August 22, 2011. Owners May contact Kenworth at 1-425-828-5440 and Peterbilt at 1-940-591-4196.

Kenworth and Peterbilt safety recall no. E038r.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Fuel System

Feb 23, 2011 · NHTSA campaign 11V127000 · 4,664 vehicles

Problem: Paccar is recalling certain model year 2008-2012 Kenworth T2000, T660, T700, T800, and W900, as well as model year 2009-2012 Peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine May become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Original NHTSA wording

PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS.

Risk: The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, May cause a fire.

Original NHTSA wording

THE DISCHARGE OF ENGINE OIL ONTO EXHAUST COMPONENTS WHICH ARE HOT, SUCH AS WHEN THE ENGINE IS UNDER SIGNIFICANT LOAD, MAY CAUSE A FIRE.

Remedy & notes

Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during March 2011. Owners May contact Kenworth at 1-425-828-5440 and Peterbilt at 1-940-591-4196.

Owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Steering

Jul 2, 2010 · NHTSA campaign 10V308000 · 9,697 vehicles

Problem: Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube May be mislocated. Mislocation of the circumferential weld May allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Original NHTSA wording

PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES.

Risk: A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.

Original NHTSA wording

A SEPARATION OF THE SPLINED AND NON-SPLINED TUBES WOULD CAUSE A LOSS OF STEERING CONTROL AND INCREASE THE RISK OF A VEHICLE CRASH.

Remedy & notes

Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on July 30, 2010. Owners May contact Kenworth at 425-828-5440 and Peterbilt at 940-591-4196.

Kenworth's recall campaign number is 10KW-F & Peterbilt recall no. 0610-D. Owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Recall text as published by NHTSA and the manufacturer.

What owners complain about

Visibility1

Owner complaints filed with NHTSA; one complaint can name several areas. Not verified by NHTSA.

NHTSA investigations

Intermittent Loss of Power Steering Assist

PE20006 · opened May 1, 2020 · closed Mar 27, 2024

Summary

On May 1, 2020, the Office of Defects Investigation (ODI) opened PE20006 to investigate complaints of intermittent loss of power steering assist in Daimler Truck North America (DTNA), Volvo Trucks of North America (Volvo) and PACCAR vehicles equipped with a ZF/TRW (TRW) THP60 steering gear.Â The investigation focused on 2010-2020 DTNA Freightliner Cascadia, M2 and WST; Volvo VN, VAH and VHD and PACCAR 337, 365, 389, 567, 579 model vehicles.Field reports and interviews with fleet drivers allege that high power steering fluid temperatures could result in internal seal and bearing failures causing pressure fluctuation, affecting left and right-hand turns.Â The inability of the driver to steer the vehicle as intended can increase the risk of a crash and injury. ODI analyzed data provided by TRW, DTNA, Volvo, and PACCAR in response to individual information request letters.ODI found that most failures occurred within the first two years and/or 50,000 miles of service. Â The claim rate decreased with time and miles in service and remained less than 0.5%. ODI normalized data from each of the manufacturers and determined that there was not a substantial difference in the failures.Additionally, TRW improved a seal in the steering gear in December 2015.Trucks built on or after 2016 (as 2017 and newer model years) show a decreasing trend of failures. In view of the overall low failure rate, the nature of early-life failure, and failure rate trending downward for model years 2017 and n…

2010 vs. other Peterbilt 386 years

Owner complaints by model year; the darker bar is the 2010. Click a bar to switch year.

Questions

Does the 2010 Peterbilt 386 have recalls?

Yes — NHTSA lists 5 recall campaigns covering the 2010 Peterbilt 386, the latest from Apr 6, 2020 (electronic stability control). A recall applies to specific vehicles: enter your VIN at nhtsa.gov/recalls to see whether yours is affected and still open.

What are the most common problems with the 2010 Peterbilt 386?

Owner complaints filed with NHTSA most often mention visibility (1). Complaints are consumer reports and are not verified by NHTSA.