2014 Nissan Versa Note recalls and problems

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been n…

On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obst…

On May 20, 2014, ODI opened PE14-014 based on eight complaints alleging incidents of excessive brake pedal travel in model year (MY) 2013 through 2014 Nissan Sentra, Versa Sedan and Versa Note passenger cars (Figure 1) and information in Early Warning Reporting field reports indicating issues with master cylinder internal seals.In response to an information request letter sent by ODI, Nissan identified a condition with the master cylinder in early production subject vehicles that could result in a slow internal leak past one of the recuperating seals to the brake reservoir when the brake pedal is depressed very slowly or lightly (Figure 2).The subject vehicles are equipped with fixed seal master cylinders supplied by TRW.To address concerns with water hammer noise with the standard seal design, the master cylinders in the early production subject vehicles used AWH (anti-water hammer) seals.The AWH seals are sensitive to contamination from assembly plant cleanliness issues, which can produce the internal leak condition during slow or light brake applies but perform as designed with normal or emergency brake applications.TRW indicated that the risk of contamination interacting with the subject seals is greatest after the evacuation and pressure fill process used to fill the brake system during the manufacturing process (early life issue).TRW developed a new master cylinder seal design (EVO seal) that addresses the noise concern and eliminates the internal leak concern associate…