2010 Kenworth W900 recalls and problems

The 2010 Kenworth W900 has 9 recalls and 0 owner complaints on file with NHTSA.

How the 2010 compares

Too few model years with complaints to compare.

9recalls

0complaints

0crashes

0fires

0injuries

—median miles

Owner complaints filed with NHTSA, not verified and not adjusted for sales. Ranking compares this model's own years only.

Does your car have an open recall?
Recalls apply to specific vehicles. Only a VIN lookup on NHTSA's official site shows whether yours is affected and still unrepaired.

Check your VIN →

9 recalls

Service Brakes

Feb 23, 2024 · NHTSA campaign 24V145000 · 936 vehicles

Problem: PACCAR Incorporated (PACCAR) is recalling certain 2009-2021 Kenworth C500, 2012-2021 Kenworth T440, 2009-2015 Kenworth T660, 2015-2024 Kenworth T680, 2009-2024 Kenworth T800, 2009-2020 Kenworth T370, 2014-2023 Kenworth T880, 2011-2016 Kenworth T470, 2023 Kenworth T480, and 2009-2019 Kenworth W900 vehicles. The air tanks have an insufficient volume of air for the brake system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 121, "Air Brake Systems."

Risk: Insufficient air volume can reduce braking performance and increase the risk of a crash.

Remedy & notes

Dealers will install the correct volume air tanks, free of charge. Owner notification letters were mailed August 12, 2024. Additional owner notification letters were mailed October 27, 2025. Owners may contact PACCAR customer service at 1-425-828-5888. PACCAR's number for this recall is 24KWD.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

Electronic Stability Control

Apr 6, 2020 · NHTSA campaign 20V199000 · 460,515 vehicles

Problem: PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk: If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Remedy & notes

PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1-425-828-5888 or Peterbilt customer service at 1-940-591-4220. PACCAR's number for this recall is 20pbc AND 20KWB.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Engine

May 26, 2015 · NHTSA campaign 15V309000 · 4,823 vehicles

Problem: PACCAR Incorporated (PACCAR) is recalling certain model year 2010-2016 Kenworth T440, T800, and W900 trucks manufactured August 31, 2009, to April 20, 2015, and 2008-2015 Peterbilt 320, 337, 348, 365, 382, and 384 trucks manufactured July 27, 2007, to April 28, 2015, and equipped with certain Cummins Westport ISL G engines. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation breather, possibly allowing engine oil to come into contact with hot surfaces.

Risk: If engine oil comes into contact with a hot surface, there is an increased risk of a fire.

Remedy & notes

Cummins will notify owners on behalf of PACCAR, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Kenworth customer service at 1-425-828-5000, Peterbilt customer service at 1-940-591-4000 or Cummins Inc. at 1-800-343-7357. PACCAR's number for this recall is 15KWH and 515-G.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Service Brakes

Nov 18, 2013 · NHTSA campaign 13V573000 · 18 vehicles

Problem: PACCAR is recalling certain model year 2007-2014 Kenworth T800 and W900 trucks manufactured March 22, 2006, through July 15, 2013 and equipped with Primaax tridem rear suspensions and a pusher and/or tag axle. The affected trucks have brake chambers that take longer to apply or release the brakes than the required time limit. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 121, "Air Brake Systems."

Risk: Brakes that take longer to apply may lengthen the distance needed to stop the truck, increasing the risk of a crash.

Remedy & notes

PACCAR will notify owners, and dealers will modify the air brake system, free of charge. The recall began on January 15, 2014. Owners may contact PACCAR at 1-425-468-7400. Kenworth's recall number is 13KWL.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Fuel System

Feb 23, 2011 · NHTSA campaign 11V127000 · 4,664 vehicles

Problem: Paccar is recalling certain model year 2008-2012 Kenworth T2000, T660, T700, T800, and W900, as well as model year 2009-2012 Peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine May become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Original NHTSA wording

PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2012 KENWORTH T2000, T660, T700, T800, AND W900, AS WELL AS MODEL YEAR 2009-2012 PETERBILT 365, 367, 384, 386, 387, 388, 389, AND 587 TRUCKS EQUIPPED WITH PACCAR MX ENGINES. THE OIL MODULE CENTRIFUGAL SPINNER FILTER CAP IN THE PACCAR MX ENGINE MAY BECOME LOOSE, POSSIBLY ALLOWING THE CAP TO COME OFF AND ENGINE OIL TO PARTIALLY DISCHARGE FROM THE OIL MODULE ONTO EXHAUST COMPONENTS.

Risk: The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, May cause a fire.

Original NHTSA wording

THE DISCHARGE OF ENGINE OIL ONTO EXHAUST COMPONENTS WHICH ARE HOT, SUCH AS WHEN THE ENGINE IS UNDER SIGNIFICANT LOAD, MAY CAUSE A FIRE.

Remedy & notes

Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during March 2011. Owners May contact Kenworth at 1-425-828-5440 and Peterbilt at 1-940-591-4196.

Owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Service Brakes

Oct 27, 2010 · NHTSA campaign 10V535000 · 417 vehicles

Problem: Paccar is recalling certain model year Kenworth T660, T700, T800 and W900 vehicles manufactured from December 22, 2008, through August 2, 2010, and equipped with AG400L air disc brakes. The air disc brake caliper could be installed on the wrong side of the drive axle potentially causing interference with the suspension bracket and the rear suspension as the outermost brake pads wear and the floating caliper moves inboard.

Original NHTSA wording

PACCAR IS RECALLING CERTAIN MODEL YEAR KENWORTH T660, T700, T800 AND W900 VEHICLES MANUFACTURED FROM DECEMBER 22, 2008, THROUGH AUGUST 2, 2010, AND EQUIPPED WITH AG400L AIR DISC BRAKES. THE AIR DISC BRAKE CALIPER COULD BE INSTALLED ON THE WRONG SIDE OF THE DRIVE AXLE POTENTIALLY CAUSING INTERFERENCE WITH THE SUSPENSION BRACKET AND THE REAR SUSPENSION AS THE OUTERMOST BRAKE PADS WEAR AND THE FLOATING CALIPER MOVES INBOARD.

Risk: As this interference gets larger, this could eventually lead to reduced braking performance, increasing the risk of a crash.

Original NHTSA wording

AS THIS INTERFERENCE GETS LARGER, THIS COULD EVENTUALLY LEAD TO REDUCED BRAKING PERFORMANCE, INCREASING THE RISK OF A CRASH.

Remedy & notes

Dealers will verify the correct orientation of the brake caliper and perform the necessary repair free of charge. The safety recall began on November 24, 2010. Owners May contact Kenworth at 425-828-5440.

Kenworth safety recall no. 10KWH.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Steering

Jul 2, 2010 · NHTSA campaign 10V308000 · 9,697 vehicles

Problem: Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube May be mislocated. Mislocation of the circumferential weld May allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Original NHTSA wording

PACCAR IS RECALLING CERTAIN MODEL YEAR 2008-2010 TRUCKS EQUIPPED WITH TRW STEERING SHAFTS. THE CIRCUMFERENTIAL WELD AROUND THE STEERING SHAFT TUBE THAT WELDS THE SPLINED TUBE TO THE NON-SPLINED TUBE MAY BE MISLOCATED. MISLOCATION OF THE CIRCUMFERENTIAL WELD MAY ALLOW THE SPLINED TUBE AND NON-SPLINED TUBE TO ROTATE RELATIVE TO ONE ANOTHER DURING A LOW SPEED, HIGH TORQUE TURN, POSSIBLY RESULTING IN A SEPARATION OF THE TWO TUBES.

Risk: A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.

Original NHTSA wording

A SEPARATION OF THE SPLINED AND NON-SPLINED TUBES WOULD CAUSE A LOSS OF STEERING CONTROL AND INCREASE THE RISK OF A VEHICLE CRASH.

Remedy & notes

Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on July 30, 2010. Owners May contact Kenworth at 425-828-5440 and Peterbilt at 940-591-4196.

Kenworth's recall campaign number is 10KW-F & Peterbilt recall no. 0610-D. Owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Suspension

May 4, 2010 · NHTSA campaign 10V185000 · 21 vehicles

Problem: Kenworth is recalling certain model year 2010 T2000, T660, T800 and W900 vehicles manufactured between July 30, 2009 and September 18, 2009. The rear axle outer end hub May have not been primed with oil properly during the rear axle installation process. Potential lack of oil May cause the outer end bearing to heat up and/or seize, possibly resulting in the overheating of the wheel end.

Original NHTSA wording

KENWORTH IS RECALLING CERTAIN MODEL YEAR 2010 T2000, T660, T800 AND W900 VEHICLES MANUFACTURED BETWEEN JULY 30, 2009 AND SEPTEMBER 18, 2009. THE REAR AXLE OUTER END HUB MAY HAVE NOT BEEN PRIMED WITH OIL PROPERLY DURING THE REAR AXLE INSTALLATION PROCESS. POTENTIAL LACK OF OIL MAY CAUSE THE OUTER END BEARING TO HEAT UP AND/OR SEIZE, POSSIBLY RESULTING IN THE OVERHEATING OF THE WHEEL END.

Risk: A wheel end fire May occur, increasing the risk of a crash.

Original NHTSA wording

A WHEEL END FIRE MAY OCCUR, INCREASING THE RISK OF A CRASH.

Remedy & notes

Dealers will replace the bearings, seals and will add oil to the outer end hub as well as inspect races and axle housing for damage and replacing as necessary free of charge. The safety recall began on May 24, 2010. Owners May contact Kenworth at 425-828-5440.

Kenworth recall no. 10KWB.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Power Train

Oct 21, 2009 · NHTSA campaign 09V415000 · 914 vehicles

Problem: Kenworth is recalling model year 2009 through 2010 T2000, T800, T660 and W900 trucks manufactured between November 12, 2008 and September 30, 2009. The axle u-bolts attaching the axle to the suspension leaf spring on certain AG400L rear suspensions May have received insufficient fastener torque during the installation process. The insufficient torque May allow the axle u-bolt to become loose, which May cause vibration in the rear suspension.

Original NHTSA wording

KENWORTH IS RECALLING MODEL YEAR 2009 THROUGH 2010 T2000, T800, T660 AND W900 TRUCKS MANUFACTURED BETWEEN NOVEMBER 12, 2008 AND SEPTEMBER 30, 2009. THE AXLE U-BOLTS ATTACHING THE AXLE TO THE SUSPENSION LEAF SPRING ON CERTAIN AG400L REAR SUSPENSIONS MAY HAVE RECEIVED INSUFFICIENT FASTENER TORQUE DURING THE INSTALLATION PROCESS. THE INSUFFICIENT TORQUE MAY ALLOW THE AXLE U-BOLT TO BECOME LOOSE, WHICH MAY CAUSE VIBRATION IN THE REAR SUSPENSION.

Risk: If multiple fasteners were to become loose, the rear axle May shift relative to the rear suspension leaf spring, which can result in loss of control and a crash.

Original NHTSA wording

IF MULTIPLE FASTENERS WERE TO BECOME LOOSE, THE REAR AXLE MAY SHIFT RELATIVE TO THE REAR SUSPENSION LEAF SPRING, WHICH CAN RESULT IN LOSS OF CONTROL AND A CRASH.

Remedy & notes

Dealers will inspect the axle u-bolts for visible defects, including bent and/or smashed threads and re-torque the axle u-bolts to factory specifications. The recall began on November 4, 2009. Owners May contact Kenworth at 425-828-5440.

Kenworth recall no. 09KWA.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Recall text as published by NHTSA and the manufacturer.

2010 vs. other Kenworth W900 years

Owner complaints by model year; the darker bar is the 2010. Click a bar to switch year.

Questions

Does the 2010 Kenworth W900 have recalls?

Yes — NHTSA lists 9 recall campaigns covering the 2010 Kenworth W900, the latest from Feb 23, 2024 (service brakes). A recall applies to specific vehicles: enter your VIN at nhtsa.gov/recalls to see whether yours is affected and still open.

What are the most common problems with the 2010 Kenworth W900?

Few complaints have been filed with NHTSA for the 2010 Kenworth W900.