2003 Honda CR-V recalls and problems

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been n…

The Office of Defects Investigation (ODI) opened PE14-016 in June 2014 based on six inflator rupture incidents involving consumer owned vehicles produced by five vehicle manufacturers.All six vehicles were operated in Florida or Puerto Rico at the time of the rupture and for the majority of their service life, and were equipped with inflators produced by Takata, a tier-one supplier of automotive air bag systems.During the course of PE14-016, ODI determined that five additional vehicle manufacturers used inflators of a similar design and vintage also supplied by Takata. No evidence of field failures was found in vehicles produced by these five additional manufacturers.Nonetheless, at ODI's insistence, all 10 vehicle manufacturers initiated a regional recall within approximately two weeks of the opening of the investigation.The regions recalled initially included Florida, Puerto Rico, Hawaii, and the U.S. Virgin Islands, areas with high absolute humidity and climatic conditions believed to be a significant factor in the inflator ruptures.As part of the recall actions, inflators removed from remedied vehicles are to be returned to Takata for testing.Takata's initial test results on passenger inflators from remedied vehicles indicated a much higher than anticipated rupture frequency for inflators returned from Florida.Accordingly ODI requested all 10 manufacturers expand the regional recalls for passenger inflators to include other geographic areas where high absolute humidity co…

The Office of Defects Investigation (ODI) opened PE14-016 in June 2014 based on six inflator rupture incidents involving consumer owned vehicles produced by five vehicle manufacturers.All six vehicles were operated in Florida or Puerto Rico at the time of the rupture and for the majority of their service life, and were equipped with inflators produced by Takata, a tier-one supplier of automotive air bag systems.During the course of PE14-016, ODI determined that five additional vehicle manufacturers used inflators of a similar design and vintage also supplied by Takata. No evidence of field failures was found in vehicles produced by these five additional manufacturers.Nonetheless, at ODI's insistence, all 10 vehicle manufacturers initiated a regional recall within approximately two weeks of the opening of the investigation.The regions recalled initially included Florida, Puerto Rico, Hawaii, and the U.S. Virgin Islands, areas with consistently high absolute humidity and climatic conditions believed to be a significant factor in the inflator ruptures.As part of the recall actions, inflators removed from remedied vehicles are to be returned to Takata for testing.Takata's initial test results on passenger inflators from remedied vehicles indicated a much higher than anticipated rupture frequency for inflators returned from Florida.Accordingly, ODI requested all 10 manufacturers expand the regional recalls for passenger inflators to include other geographic areas where high absolu…

This investigation was prompted by Preliminary Evaluation (PE) 11-017, and was based on reports from consumers alleging that both low beam headlights stopped illuminating simultaneously.Some complainants also reported that the combination switch (switch) that controls the headlights and turn signals, and/or its electrical wiring harness connector were damaged by overheating.ODI's PE information request letter asked Honda for certain data on model years (MY) 2002-2006 CR-V, 2003-2008 Pilot, 2003-2008 Element, 2001-2005 Civic, and 2000-2001 S 2000 vehicles.Analysis of complaint and Honda data show that a complete low beam headlight circuit failure occurs in models with 2-bulb headlight systems (i.e., a single bulb on each side for high and low beam).Models with 2-bulb systems include MY 2002-2004 CR-V, 2003-2005 Pilot, 2001-2003 Civic, and 2003-2008 Element.Models with 4-bulb headlight systems (i.e., two bulbs on each side, one for high and one for low beam) have different electrical circuits for the headlights and do not experience the same failure mechanism as the 2-bulb system.MY 2000-2001 S 2000 models with 2-bulb high intensity discharge headlights also have different electrical circuits for the headlights and do not experience the same failure mechanism.Honda introduced the 4-bulb headlight system in CR-V in MY 2005, in Pilot in MY 2006, and in Civic in MY 2004.On March 29, 2012 Honda submitted a defect information report (DIR) to recall 554,428 vehicles, including MY 200…

The Office of Defects Investigation (ODI) opened this investigation based on 12 reports from consumers alleging the low beam headlights stopped working simultaneously.Several of the complainants reported that the headlight switch and/or its wiring harness connector required replacement to repair the low beam headlight circuit, and also reported that the switch and/or the wire harness connector were damaged from overheating.Based on information provided by Honda in response to ODI's Preliminary Evaluation information request, ODI is upgrading the investigation to EA11-012.

This investigation was prompted by Preliminary Evaluation (PE) 10-047 and was based on reports from consumers alleging that smoke and/or fire, as defined in 49 CFR ? 579.4, had occurred inside of the driver's door.The subject vehicles, model year (MY) 2006 CR-V, were manufactured at two different assembly plants.The vehicles manufactured in Japan (Sayama plant) were produced with a power window master switch (PWMS) supplied by the Thai Toyo Denso Company, Ltd. (Denso).The vehicles manufactured in the United Kingdom (UK, Swindon, England plant) were produced with a PWMS supplied by the Omron Corporation (Omron).Honda provided 45 reports on the subject vehicles responsive to this investigation.Of this number, 24 reports concerned Japan-built vehicles, 19 reports on UK-built vehicles, and two reports without a vehicle identification number which could not be identified by assembly plant. Four of Honda's reports were duplicative of ODI reports.ODI received nine reports on the subject vehicles:five on Japan-built and four on UK-built vehicles, and one additional report on a MY 2005 UK built vehicle.The ODI reports can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers: 10343884, 10307287, 10321646, 10375324, 10386750, 10425406, 10437807, 10439880, 10469350, and 10406979.In most cases, it was reported that the PWMS and/or its electrical wiring harness had sustained heat related damage requiring replacement of the affect…

IN DOCUMENTS PROVIDED DURING EA04-027, HONDA IDENTIFIED A MECHANISM WHICH CAUSES THE RUBBER SEAL (GASKET) OF THE ORIGINAL EQUIPMENT (OE) OIL FILTER TO ADHERE TO THE ENGINE BLOCK OF THE SUBJECT VEHICLES.IF AN ADHERED SEAL REMAINS WHEN THE OE FILTER IS REMOVED AND A NEW FILTER IS INSTALLED, A DOUBLE GASKET CONDITION RESULTS.A SUBSEQUENT RUPTURE OF THE EXTRANEOUS SEAL CAN RESULT IN OIL CONTACTING NEARBY EXHAUST SYSTEM SURFACES AND A FIRE MAY OCCUR.THROUGHOUT ITS DISCUSSIONS WITH ODI, HONDA HAS MAINTAINED THAT IT IS THE SERVICING TECHNICIAN?S RESPONSIBILITY TO INSPECT FOR AND REMOVE THE SEAL PRIOR TO INSTALLING A NEW FILTER.ODI?S ANALYSIS FOUND THAT SEAL ADHESION, IN CONJUNCTION WITH TECHNICIAN ERROR AND EXHAUST COMPONENT LOCATION, RESULTED IN A HIGH RATE OF SUBJECT VEHICLE OIL FILTER FIRES COMPARED TO EARLIER MODELS AND PEERS.VEHICLES THAT HAVE NOT HAD THE OE FILTER DISTURBED ARE NOT AT RISK.SERVICE REPLACEMENT FILTER SEALS, WHICH ARE MANUFACTURED BY A DIFFERENT SUPPLIER, DO NOT EXHIBIT THE SEAL ADHESION CONDITION.THEREFORE, IF THE INITIAL OIL CHANGE IS DONE PROPERLY, THE ELEVATED FIRE RISK IS ELIMINATED FOR THE REMAINDER OF THE VEHICLE?S LIFE.BASED ON AVERAGE MILEAGE ACCUMULATION AND OIL SERVICE INTERVAL, ODI ESTIMATES THAT MORE THAN TWO THIRDS OF THE SUBJECT VEHICLES HAVE RECEIVED THEIR INITIAL OIL CHANGE AND ARE NO LONGER AT AN ELEVATED RISK.HONDA CHANGED THE DESIGN OF THE FILTER SEAL TO PREVENT THE ADHESION CONDITION AND INTRODUCED THE NEW SEAL AT BOTH CR-V ASSEMBLY PLANTS I…

THIS INVESTIGATION IDENTIFIED 32 INCIDENTS OF OIL FILTER LEAKAGE IN THE SUBJECT VEHICLE POPULATION, WITH 22 RESULTING IN VEHICLE FIRES.ALL OF THE INCIDENTS OCCURRED FOLLOWING OIL CHANGES.HONDA'S INVESTIGATION OF 14 OF THE FIRE INCIDENTS DETERMINED THAT FIVE OIL FILTERS HAD STACKED SEALS (DOUBLE-GASKETING), AND NINE OIL FILTERS HAD DISTORTED OR PINCHED SEALS.ACCORDING TO HONDA, BOTH CONDITIONS RESULT FROM FAILURE TO FOLLOW NECESSARY REPAIR PROCEDURES. STACKED SEALS RESULT FROM FAILURE OF THE SERVICE TECHNICIAN TO REMOVE THE OLD SEAL PRIOR TO INSTALLING THE NEW FILTER AND SEAL.DISTORTED OR PINCHED SEALS RESULT FROM FAILURE TO PROPERLY LUBRICATE THE NEW SEAL PRIOR TO INSTALLATION. OIL LEAKAGE FROM A STACKED, DISTORTED, OR PINCHED SEAL CAN BE IGNITED BY HEAT FROM THE EXHAUST SYSTEM, WHICH IS LOCATED NEAR THE OIL FILTER IN THE SUBJECT VEHICLES.HONDA WILL ISSUE COMMUNICATIONS TO ITS DEALERS WARNING OF THE NECESSITY TO FOLLOW CORRECT PROCEDURES WHEN REPLACING OIL FILTERS IN THE SUBJECT VEHICLES AND OF THE POTENTIAL FOR VEHICLE FIRES TO RESULT FROM IMPROPER REPAIRS.ODI WILL CONTINUE TO MONITOR THE ALLEGED DEFECT IN MY 2003 AND LATER CR-V VEHICLES.THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.