2001 Ford Windstar recalls and problems

The 2001 Ford Windstar has 15 recalls and 1,686 owner complaints on file with NHTSA; the most reported problem area is service brakes.

2001 Ford Windstar
Photo: 2001 Ford Windstar by Elise240SX, CC BY-SA 4.0, via Wikimedia Commons
How the 2001 compares
Fewest complaintsMost complaints

Highest complaint count among 6 Windstar model years — the most of any year.

15recalls
1,686complaints
66crashes
62fires
62injuries
108,000median miles

Owner complaints filed with NHTSA, not verified and not adjusted for sales. Ranking compares this model's own years only.

Does your car have an open recall?
Recalls apply to specific vehicles. Only a VIN lookup on NHTSA's official site shows whether yours is affected and still unrepaired.
Check your VIN →

15 recalls

Suspension

Sep 29, 2015 · NHTSA campaign 15V608000 · 283,413 vehicles

Problem: Ford Motor Company (Ford) is recalling certain model year 1998-2003 Windstar vehicles manufactured September 2, 1997, to July 3, 2003. The affected vehicles were previously remedied to safeguard against the rear axle cracking from corrosion, however, the remedy brackets may have been misinstalled. The incorrect bracket installations may limit the effectiveness of the service repair for NHTSA recalls 10V-385, 12V-193, and 12V-195.

Risk: If the brackets were not installed properly, the rear axle may fracture, affecting the vehicle handling and increasing the risk of a crash.

Remedy & notes

Ford will notify owners, and dealers will inspect the brackets to verify their proper installation. If a bracket is found to have been misinstalled, the rear axle will be replaced. These repairs will be performed free of charge. The began on October 21, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S27.

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Suspension

May 3, 2012 · NHTSA campaign 12V195000 · 9,192 vehicles

Problem: Ford is recalling certain model year 1998-2003 windstar vehicles manufactured from September 1, 1997, through July 3, 2003, registered in Puerto Rico. Due to increased stresses caused by high cycles of torsional loading, specific to this market, the rear axle can crack.

Original NHTSA wording

FORD IS RECALLING CERTAIN MODEL YEAR 1998-2003 WINDSTAR VEHICLES MANUFACTURED FROM SEPTEMBER 1, 1997, THROUGH JULY 3, 2003, REGISTERED IN PUERTO RICO. DUE TO INCREASED STRESSES CAUSED BY HIGH CYCLES OF TORSIONAL LOADING, SPECIFIC TO THIS MARKET, THE REAR AXLE CAN CRACK.

Risk: A fractured axle May result in a loss of vehicle control, increasing the risk of a crash.

Original NHTSA wording

A FRACTURED AXLE MAY RESULT IN A LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy & notes

Ford will notify owners, and dealers will inspect and install a reinforcement bracket on the rear axle or replace the axles, as necessary. This service will be provided free of charge. The recall began on June 1, 2012. Owners May contact the Ford motor company customer relationship center at 1-866-436-7332.

Ford's safety recall campaign number is 12S30.customers May contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.

Suspension

May 3, 2012 · NHTSA campaign 12V194000 · 23,000 vehicles

Problem: Ford is recalling certain model year 1999-2003 windstar vehicles originally sold in or currently registered in the state of Virginia. Corrosion-related fractures of the front lower control arm rear attaching brackets and body mount attachments May occur.

Original NHTSA wording

FORD IS RECALLING CERTAIN MODEL YEAR 1999-2003 WINDSTAR VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATE OF VIRGINIA. CORROSION-RELATED FRACTURES OF THE FRONT LOWER CONTROL ARM REAR ATTACHING BRACKETS AND BODY MOUNT ATTACHMENTS MAY OCCUR.

Risk: A separation of a front lower control arm rear attaching bracket May result in a lower control arm separation. A separation of both front subframe rear body mounts May result in separation of the steering intermediate shaft. Either condition could result in significant loss of steering control, increasing the risk of a crash.

Original NHTSA wording

A SEPARATION OF A FRONT LOWER CONTROL ARM REAR ATTACHING BRACKET MAY RESULT IN A LOWER CONTROL ARM SEPARATION. A SEPARATION OF BOTH FRONT SUBFRAME REAR BODY MOUNTS MAY RESULT IN SEPARATION OF THE STEERING INTERMEDIATE SHAFT. EITHER CONDITION COULD RESULT IN SIGNIFICANT LOSS OF STEERING CONTROL, INCREASING THE RISK OF A CRASH.

Remedy & notes

Dealers will inspect both front lower control arm rear attaching brackets and both body mount attachments at the rear of the front subframe and make the necessary repairs free of charge. The recall began on June 18, 2012. Owners May contact Ford at 1-866-436-7332.

Ford's recall campaign number is 11S16.customers May contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.

Power Train

May 3, 2012 · NHTSA campaign 12V193000 · 27,000 vehicles

Problem: Ford is recalling certain model year 1998-2003 windstar vehicles manufactured from September 1, 1997, through July 3, 2003, and currently registered or originally sold in Virginia. Over time, corrosion can weaken the rear axle making it susceptible to torsional stress. Corrosion and stress can lead to cracks which, if undetected, can increase and result in a complete fracture of the axle.

Original NHTSA wording

FORD IS RECALLING CERTAIN MODEL YEAR 1998-2003 WINDSTAR VEHICLES MANUFACTURED FROM SEPTEMBER 1, 1997, THROUGH JULY 3, 2003, AND CURRENTLY REGISTERED OR ORIGINALLY SOLD IN VIRGINIA. OVER TIME, CORROSION CAN WEAKEN THE REAR AXLE MAKING IT SUSCEPTIBLE TO TORSIONAL STRESS. CORROSION AND STRESS CAN LEAD TO CRACKS WHICH, IF UNDETECTED, CAN INCREASE AND RESULT IN A COMPLETE FRACTURE OF THE AXLE.

Risk: A fractured axle can affect vehicle handling and increase the risk of a crash.

Original NHTSA wording

A FRACTURED AXLE CAN AFFECT VEHICLE HANDLING AND INCREASE THE RISK OF A CRASH.

Remedy & notes

Ford will notify owners, and dealers will inspect and install rear axle reinforcement brackets, or replace the axles, as necessary. This service will be performed free of charge. The recall began on June 19, 2012. Owners May contact Ford at 1-866-436-7332.

Ford's recall campaign number is 10S13.customers May contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty: 1-800-424-9153); or go to http://www.safercar.gov.

Structure

Jan 26, 2011 · NHTSA campaign 11V030000 · 425,288 vehicles

Problem: Ford is recalling certain model year 1999-2003 windstar vehicles originally sold in or currently registered in the states of Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Utah, Vermont, West Virginia, and Wisconsin. A separation of a front lower control arm rear attaching bracket May result in a lower control arm separation. A separation of both front subframe rear body mounts May result in separation of the steering intermediate shaft.

Original NHTSA wording

FORD IS RECALLING CERTAIN MODEL YEAR 1999-2003 WINDSTAR VEHICLES ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, THE DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, UTAH, VERMONT, WEST VIRGINIA, AND WISCONSIN. A SEPARATION OF A FRONT LOWER CONTROL ARM REAR ATTACHING BRACKET MAY RESULT IN A LOWER CONTROL ARM SEPARATION. A SEPARATION OF BOTH FRONT SUBFRAME REAR BODY MOUNTS MAY RESULT IN SEPARATION OF THE STEERING INTERMEDIATE SHAFT.

Risk: This could result in reduced steering control increasing the risk of a crash.

Original NHTSA wording

THIS COULD RESULT IN REDUCED STEERING CONTROL INCREASING THE RISK OF A CRASH.

Remedy & notes

Dealers will inspect both front lower control arm rear attaching brackets, and both body mount attachments at the rear of the front subframe, and make the necessary repairs free of charge. If repairs cannot be made to a vehicle, Ford will offer to repurchase the vehicle. The safety recall is expected to begin on or before February 21, 2011. Owners May contact Ford at 1-866-436-7332.

Ford's safety recall no. 11S16.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Suspension

Aug 26, 2010 · NHTSA campaign 10V385000 · 492,650 vehicles

Problem: Ford is recalling certain model year 1998-2003 windstar vehicles manufactured from September 1, 1997 through February 28, 2003 and currently registered or originally sold in Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, and Wisconsin. After many years of vehicle service in these areas, corrosion can weaken the rear axle, making it susceptible to torsional stress. Corrosion and stress can lead to cracks which if undetected can propagate and result in a complete fracture of the axle.

Original NHTSA wording

FORD IS RECALLING CERTAIN MODEL YEAR 1998-2003 WINDSTAR VEHICLES MANUFACTURED FROM SEPTEMBER 1, 1997 THROUGH FEBRUARY 28, 2003 AND CURRENTLY REGISTERED OR ORIGINALLY SOLD IN CONNECTICUT, DELAWARE, DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, KENTUCKY, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, AND WISCONSIN. AFTER MANY YEARS OF VEHICLE SERVICE IN THESE AREAS, CORROSION CAN WEAKEN THE REAR AXLE, MAKING IT SUSCEPTIBLE TO TORSIONAL STRESS. CORROSION AND STRESS CAN LEAD TO CRACKS WHICH IF UNDETECTED CAN PROPAGATE AND RESULT IN A COMPLETE FRACTURE OF THE AXLE.

Risk: A fractured axle can affect vehicle handling and increase the risk of a crash.

Original NHTSA wording

A FRACTURED AXLE CAN AFFECT VEHICLE HANDLING AND INCREASE THE RISK OF A CRASH.

Remedy & notes

As parts become available, dealers will inspect and if necessary install the rear axle reinforcement brackets free of charge. This service will be performed free of charge. The safety recall began on October 20, 2010. Owners May contact Ford at 1-866-436-7332.

Ford's recall no. Is 10S13.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Vehicle Speed Control

Oct 13, 2009 · NHTSA campaign 09V399000 · 4,500,000 vehicles

Problem: Ford is recalling model years 1995-2003 windstar, 2000-2003 excursion diesel, 1993-1997 and 1999-2003 f-250 sd through f-550 sd diesel, 1992-2003 e-150 through e-550, 1995-2002 explorer, 1997 and 2002 Mercury mountaineer, 1995-1997 and 2001-2003 ranger, and 1994 F53 vehicles equipped with the Texas instruments speed control deactivation switch (scds). The scds May leak internally and then overheat, smoke, or burn.

Original NHTSA wording

FORD IS RECALLING MODEL YEARS 1995-2003 WINDSTAR, 2000-2003 EXCURSION DIESEL, 1993-1997 AND 1999-2003 F-250 SD THROUGH F-550 SD DIESEL, 1992-2003 E-150 THROUGH E-550, 1995-2002 EXPLORER, 1997 AND 2002 MERCURY MOUNTAINEER, 1995-1997 AND 2001-2003 RANGER, AND 1994 F53 VEHICLES EQUIPPED WITH THE TEXAS INSTRUMENTS SPEED CONTROL DEACTIVATION SWITCH (SCDS). THE SCDS MAY LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Risk: A vehicle fire could occur with or without the engine running.

Original NHTSA wording

A VEHICLE FIRE COULD OCCUR WITH OR WITHOUT THE ENGINE RUNNING.

Remedy & notes

Ford will notify owners that dealers will install a fused wiring harness in line with the scds. On 1999-2003 windstar vehicles with a leaking scds, dealers will also inspect the ABS control module connector and repair as necessary. Repairs will be completed free of charge. The safety recall began on October 27, 2009. Owners May contact Ford at 1-888-222-2751.

Ford's recall campaign number is 09S09.owners May also contact the national highway traffic safety administration's vehicle safety hotline at 1-888-327-4236 (tty 1-800-424-9153), or go to <a href=http://www.safercar.gov>http://www.safercar.gov</a> .

Seats

Nov 6, 2003 · NHTSA campaign 03V459000 · 257,119 vehicles

Problem: Certain minivans fail to comply with the requirements of federal motor vehicle safety standard no. 225, "child restraint anchorage system." during testing, a third row bench floor-to-seat latch released before the strength requirement was met. Identical latches are used in the second row of seats.

Original NHTSA wording

CERTAIN MINIVANS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 225, "CHILD RESTRAINT ANCHORAGE SYSTEM." DURING TESTING, A THIRD ROW BENCH FLOOR-TO-SEAT LATCH RELEASED BEFORE THE STRENGTH REQUIREMENT WAS MET. IDENTICAL LATCHES ARE USED IN THE SECOND ROW OF SEATS.

Risk: If the latches on TH4E second or third row seats of the vehicle release in a crash, the potential for occupant injury is increased.

Original NHTSA wording

IF THE LATCHES ON TH4E SECOND OR THIRD ROW SEATS OF THE VEHICLE RELEASE IN A CRASH, THE POTENTIAL FOR OCCUPANT INJURY IS INCREASED.

Remedy & notes

Dealers will replace the seat-to-floor latches on the second and third row of seats. Owner notification began on November 21, 2003. Owners should contact Ford at 1-800-392-3673.

Ford recall no. 03C05.also, customers can contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Trailer Hitches

Mar 11, 2002 · NHTSA campaign 02V072000 · 417,037 vehicles

Problem: In some minivans, water and other contaminants (dirt, salt, etc.) can enter into the right rear passenger compartment due to a missing body sealer.

Original NHTSA wording

IN SOME MINIVANS, WATER AND OTHER CONTAMINANTS (DIRT, SALT, ETC.) CAN ENTER INTO THE RIGHT REAR PASSENGER COMPARTMENT DUE TO A MISSING BODY SEALER.

Risk: This could cause a short circuit in the electrical connector at the rear wire harness. A short circuit can lead to malfunctions of the rear lighting system, reverse park-aid system, or trailer tow electrical system. A sustained short circuit can result in melted connectors and potentially lead to a fire.

Original NHTSA wording

THIS COULD CAUSE A SHORT CIRCUIT IN THE ELECTRICAL CONNECTOR AT THE REAR WIRE HARNESS. A SHORT CIRCUIT CAN LEAD TO MALFUNCTIONS OF THE REAR LIGHTING SYSTEM, REVERSE PARK-AID SYSTEM, OR TRAILER TOW ELECTRICAL SYSTEM. A SUSTAINED SHORT CIRCUIT CAN RESULT IN MELTED CONNECTORS AND POTENTIALLY LEAD TO A FIRE.

Remedy & notes

Dealers will inspect the electrical connector and surrounding area for absence of body sealing and corrosion. If corrosion is present, dealers will service the body gaps, repair corroded connectors, and apply a protective patch to the connector assembly and body hole. If corrosion is not present but the body sealer is missing, dealers will service the body gaps and apply a protective patch to the connector assembly and body hole. Owner notification began April 5, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Customers can also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Equipment

Aug 15, 2001 · NHTSA campaign 01V262000 · 413,245 vehicles

Problem: Vehicle description: MINI vans equipped with auxiliary rear air-conditioning. If the auxiliary air-conditioning blower motor stops turning while in the medium-low blower speed setting, there is the potential that the resistor May become hot and smoke.

Original NHTSA wording

VEHICLE DESCRIPTION: MINI VANS EQUIPPED WITH AUXILIARY REAR AIR-CONDITIONING. IF THE AUXILIARY AIR-CONDITIONING BLOWER MOTOR STOPS TURNING WHILE IN THE MEDIUM-LOW BLOWER SPEED SETTING, THERE IS THE POTENTIAL THAT THE RESISTOR MAY BECOME HOT AND SMOKE.

Risk: The motor could potentially catch on fire.

Original NHTSA wording

THE MOTOR COULD POTENTIALLY CATCH ON FIRE.

Remedy & notes

Dealers will install a jumper wire that will ensure that the medium-low blower speed setting is protected by the thermal limiter. Owner notification began augsut 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Visibility

Aug 15, 2001 · NHTSA campaign 01V261000 · 598,256 vehicles

Problem: Vehicle description: MINI vans. Contaminants such as water, salt, and windshield washer solution can enter the wiper motor cover assembly through pinholes on the exterior of the cover that are used in the molding process. In addition, on certain of the vehicles built between February and August 2000, a switch located in the plastic cover of the wiper motor gear case could malfunction and overheat. Either of these conditions could potentially result in loss of intermittent wiper function, loss of wiper park function, complete loss of wiper function, smoke, or ignition of the plastic cover material. Contaminant entry could also result in unintended wiper motor operation.

Original NHTSA wording

VEHICLE DESCRIPTION: MINI VANS. CONTAMINANTS SUCH AS WATER, SALT, AND WINDSHIELD WASHER SOLUTION CAN ENTER THE WIPER MOTOR COVER ASSEMBLY THROUGH PINHOLES ON THE EXTERIOR OF THE COVER THAT ARE USED IN THE MOLDING PROCESS. IN ADDITION, ON CERTAIN OF THE VEHICLES BUILT BETWEEN FEBRUARY AND AUGUST 2000, A SWITCH LOCATED IN THE PLASTIC COVER OF THE WIPER MOTOR GEAR CASE COULD MALFUNCTION AND OVERHEAT. EITHER OF THESE CONDITIONS COULD POTENTIALLY RESULT IN LOSS OF INTERMITTENT WIPER FUNCTION, LOSS OF WIPER PARK FUNCTION, COMPLETE LOSS OF WIPER FUNCTION, SMOKE, OR IGNITION OF THE PLASTIC COVER MATERIAL. CONTAMINANT ENTRY COULD ALSO RESULT IN UNINTENDED WIPER MOTOR OPERATION.

Risk: Switch malfunction is most likely to occur when the intermittent setting of the wipers is being used, or when snow or ice obstructs the blades from returning to the "parked" position at the bottom of the windshield. Loss of visibility while driving increases the risk of a crash.

Original NHTSA wording

SWITCH MALFUNCTION IS MOST LIKELY TO OCCUR WHEN THE INTERMITTENT SETTING OF THE WIPERS IS BEING USED, OR WHEN SNOW OR ICE OBSTRUCTS THE BLADES FROM RETURNING TO THE "PARKED" POSITION AT THE BOTTOM OF THE WINDSHIELD. LOSS OF VISIBILITY WHILE DRIVING INCREASES THE RISK OF A CRASH.

Remedy & notes

Dealers will install a new wiper cover with improved sealing and water resistance. Owner notification begain August 27, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Seat Belts

Jul 16, 2001 · NHTSA campaign 01V227001 · 1,400,000 vehicles

Problem: Vehicle description: Passenger and sport utility vehicles, pickup trucks, and minivans. Equipped with seat belts supplied by trw. It is possible that the driver's and/or front passenger's outboard seat belt buckle May not fully latch. Ford crown victoria built at st. Thomas assembly plant from 4/17/00 - 5/29/01 Mercury grand marquis built at st. Thomas assembly plant from 4/17/00 - 5/29/01. Lincoln town cars built at wixom assembly plant from 3/27/00 - 5/30/01. Lincoln navigators built at Michigan truck plant from 4/11/00 - 5/31/01. Ford windstars built at oakville assembly plant from 3/23/00 - 5/30/01. Ford rangers built at twin cities plant from 3/28/00 - 5/30/01, and also at the edison plant from 3/13/00 - 5/25/01. Ford f-150 truck built at norfolk plant from 4/18/00 - 5/25/00; at ontario plant from 5/10/00 - 5/28/01; at Kansas city plant from 9/11/99 - 5/25/01; and at cuautitlan plant from 5/16/00 - 6/9/01. Ford super duty f-250, f-350, f-450, and f-550 trucks built at Kentucky plant from 4/17/00 - 5/27/01; and at cuautitlan plant from 5/16/00 - 6/19/01. Ford excursions built at Kentucky plant from 4/17/00 - 10/2/00. Ford expeditions built at Michigan truck plant from 4/11/00 - 5/31/01.

Original NHTSA wording

VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND MINIVANS. EQUIPPED WITH SEAT BELTS SUPPLIED BY TRW. IT IS POSSIBLE THAT THE DRIVER'S AND/OR FRONT PASSENGER'S OUTBOARD SEAT BELT BUCKLE MAY NOT FULLY LATCH. FORD CROWN VICTORIA BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01 MERCURY GRAND MARQUIS BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01. LINCOLN TOWN CARS BUILT AT WIXOM ASSEMBLY PLANT FROM 3/27/00 - 5/30/01. LINCOLN NAVIGATORS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01. FORD WINDSTARS BUILT AT OAKVILLE ASSEMBLY PLANT FROM 3/23/00 - 5/30/01. FORD RANGERS BUILT AT TWIN CITIES PLANT FROM 3/28/00 - 5/30/01, AND ALSO AT THE EDISON PLANT FROM 3/13/00 - 5/25/01. FORD F-150 TRUCK BUILT AT NORFOLK PLANT FROM 4/18/00 - 5/25/00; AT ONTARIO PLANT FROM 5/10/00 - 5/28/01; AT KANSAS CITY PLANT FROM 9/11/99 - 5/25/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/9/01. FORD SUPER DUTY F-250, F-350, F-450, AND F-550 TRUCKS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 5/27/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/19/01. FORD EXCURSIONS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 10/2/00. FORD EXPEDITIONS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01.

Risk: In the event of a crash, the restraint system May not provide adequate occupant protection, increasing the risk of personal injury to the seat occupant.

Original NHTSA wording

IN THE EVENT OF A CRASH, THE RESTRAINT SYSTEM MAY NOT PROVIDE ADEQUATE OCCUPANT PROTECTION, INCREASING THE RISK OF PERSONAL INJURY TO THE SEAT OCCUPANT.

Remedy & notes

Dealers will inspect the front outboard seat belt buckles and if the buckle fails the inspection process, it will be replaced. Owner notification began July 25, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-866-436-7332.

Also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Vehicle Speed Control

Jun 22, 2001 · NHTSA campaign 01V207000 · 45,800 vehicles

Problem: Vehicle description: Minivans equipped with an adjustable pedal option. The driver floor mat could interfere with the accelerator pedal.

Original NHTSA wording

VEHICLE DESCRIPTION: MINIVANS EQUIPPED WITH AN ADJUSTABLE PEDAL OPTION. THE DRIVER FLOOR MAT COULD INTERFERE WITH THE ACCELERATOR PEDAL.

Risk: This can result in a stuck throttle, increasing the risk of a crash.

Original NHTSA wording

THIS CAN RESULT IN A STUCK THROTTLE, INCREASING THE RISK OF A CRASH.

Remedy & notes

Dealers will replace both front driver and passenger side floor mats in the vehicle. Owner notification began July 6, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-800-392-3673.

Also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Air Bags

Dec 6, 2000 · NHTSA campaign 00V412000 · 16,000 vehicles

Problem: Vehicle description: Minivans and passenger vehicles. A restraint control module (rcm) or a side or front crash sensor May have been assembled with one or more of the screws that mount the circuit board in the housing missing. If some or all of the screws are missing, the performance of the occupant restrains could be affected.

Original NHTSA wording

VEHICLE DESCRIPTION: MINIVANS AND PASSENGER VEHICLES. A RESTRAINT CONTROL MODULE (RCM) OR A SIDE OR FRONT CRASH SENSOR MAY HAVE BEEN ASSEMBLED WITH ONE OR MORE OF THE SCREWS THAT MOUNT THE CIRCUIT BOARD IN THE HOUSING MISSING. IF SOME OR ALL OF THE SCREWS ARE MISSING, THE PERFORMANCE OF THE OCCUPANT RESTRAINS COULD BE AFFECTED.

Risk: In some cases, less than the intended level of protection in the event of a crash.

Original NHTSA wording

IN SOME CASES, LESS THAN THE INTENDED LEVEL OF PROTECTION IN THE EVENT OF A CRASH.

Remedy & notes

Dealers will inspect the rcm and crash sensors and, if necessary, replace them.

Owner notification began December 21, 2000. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-800-392-3673. Also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Air Bags

Sep 13, 2000 · NHTSA campaign 00V270000 · 18,500 vehicles

Problem: Certain passenger vehicles, limousines, and MINI vans were built with a newly designed restraint control module (rcm). In some cases, the rcm does not recognize certain system faults that could result in an air bag or seat belt pre-tensioner unexpectedly activating during the self-test sequence at vehicle start-up.

Original NHTSA wording

CERTAIN PASSENGER VEHICLES, LIMOUSINES, AND MINI VANS WERE BUILT WITH A NEWLY DESIGNED RESTRAINT CONTROL MODULE (RCM). IN SOME CASES, THE RCM DOES NOT RECOGNIZE CERTAIN SYSTEM FAULTS THAT COULD RESULT IN AN AIR BAG OR SEAT BELT PRE-TENSIONER UNEXPECTEDLY ACTIVATING DURING THE SELF-TEST SEQUENCE AT VEHICLE START-UP.

Risk: This condition could result in personal injury.

Original NHTSA wording

THIS CONDITION COULD RESULT IN PERSONAL INJURY.

Remedy & notes

Dealers will replace the rcm in these vehicles. Owner notification began September 14, 2000. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact Ford at 1-800-392-3673.

Also contact the national highway traffic safety administration's auto safety hotline at 1-888-DASH-2-DOT (1-888-327-4236).

Recall text as published by NHTSA and the manufacturer.

What owners complain about

Owner complaints filed with NHTSA; one complaint can name several areas. Not verified by NHTSA.

Complaints by year filed

2001: 35 complaints20012002: 52 complaints2003: 45 complaints20032004: 69 complaints2005: 54 complaints20052006: 42 complaints2007: 53 complaints20072008: 142 complaints2009: 159 complaints20092010: 377 complaints3772011: 164 complaints20112012: 105 complaints2013: 99 complaints20132014: 104 complaints2015: 75 complaints20152016: 31 complaints2017: 27 complaints20172018: 11 complaints2019: 19 complaints20192020: 5 complaints2021: 9 complaints20212022: 3 complaints2023: 6 complaints20236

NHTSA investigations

Front Subframe Corrosion Failures

EA10007 · opened Dec 20, 2010 · closed Mar 17, 2011 · led to recall 11V030000
Summary

In a January 26, 2011 Defect Information Report, Ford Motor Company (Ford) notified the National Highway Traffic Safety Administration (NHTSA) that it will conduct a safety recall to address corrosion related fractures in the front lower control arm rear attaching brackets and body mount attachments at the rear of the front subframe in approximately 425,288 model year (MY) 1999 through 2003 Ford Windstar vehicles manufactured from April 1998 to July 2003 and either sold or currently registered in the following high corrosion (Salt-Belt) states:Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Utah, Vermont, West Virginia and Wisconsin (NHTSA Recall No. 11V-030, Ford Recall No. 11S16).According to Ford, separation of a front lower control arm rear attaching bracket may result in a lower control arm separation and separations of both front subframe rear body mounts may result in separation of the steering intermediate shaft.Either condition could result in diminished vehicle directional control, increasing the risk of a crash.Dealers will inspect the lower control arm rear attachment flanges and the rear body mount sections of the subframe on the right (passenger) and left (driver) sides of the vehicle.Owners of vehicles that pass the inspection will be notified when to return for installation of reinforcement bracke…

Front Subframe Corrosion Failures

PE10026 · opened Jul 20, 2010 · closed Dec 20, 2010 · led to recall 11V030000
Summary

The Office of Defects Investigation (ODI) has identified 346 complaints to ODI and Ford alleging fracture, cracking and or excessive corrosion of the front subframes in model year (MY) 1999 through 2003 Ford Windstar vehicles.Approximately 97 percent of these complaints (334) involve vehicles that have been operated in Salt Belt states, which make up approximately 60 percent of the subject vehicle sales in the United States.The front subframe, sometimes referred to as the engine cradle, is a structural component of the Windstar vehicles that carries the engine, transaxle, steering rack and certain front suspension components (e.g., lower control arm).For complaints with sufficient information to identify the location of the failure, most describe problems with the rear mounting bracket for the front passenger-side lower control arm with some related to the rear body mount attachment located in the same general area of the subframe (right-rear section near the front passenger wheel).The remainder of the reports allege fracture of the front subframe at other or, most often, unspecified locations.Almost all of the complaints that specified the side of the vehicle indicated that the problem occurred on the right/passenger side (106), with only a few indicating the left/driver side (2) or both sides (3) were affected.Ford and several complainants attributed the right-side failures to the routing of the air-conditioning lines above the front subframe on that side of the vehicle, fu…

Rear Axle Cracking

PE10016 · opened May 13, 2010 · closed Sep 22, 2010 · led to recall 10V385000
Summary

In a letter dated August 26, 2010, Ford Motor Company (Ford) submitted a Defect Information Report notifying NHTSA that it will conduct a safety recall (NHTSA Recall No. 10V-385) to address a rear axle defect in model year (MY) 1998 through 2003 Ford Windstar vehicles built at the Oakville assembly plant from September 1, 1997 through February 28, 2003 and either sold or currently registered in high corrosion (Salt-Belt) states where the use of salt and other corrosive chemicals may be used to treat snow/ice covered roads.The following states are included in Ford's recall:Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia and Wisconsin. The subject vehicles utilize a Stamped/Formed axle assembly manufactured by Benteler automotive Corporation of Galesburg, MI.According to Ford, after many years of vehicle service in the Salt-Belt states, corrosion can weaken the rear axle, making it susceptible to torsional stress.There is a risk that the combined effects of corrosion and stress can lead to cracks which, if undetected, can propagate and result in a complete fracture of the axle.A completely fractured axle can affect vehicle handling and increase the risk of a crash.To correct the safety defect, Ford will initially inspect all of the subject vehicles brought into Ford/Lincoln-Mercury dealership…

ENGINE COMPARTMENT FIRES

EA08021 · opened Sep 17, 2008 · closed Oct 14, 2009 · led to recall 09V399000
Summary

EA08-021 IS CLOSED WITH FORD'S ACTIONS IN RECALL 09V-399 RECALLING APPROXIMATELY 4.5 MILLION VEHICLES EQUIPPED WITH TEXAS INSTRUMENTS SPEED CONTROL DEACTIVATION SWITCHES (SCDS).WITH THIS RECALL FORD HAS NOW RECALLED ALL OF THE APPROXIMATE 16 MILLION FORD MODEL VEHICLES THAT WERE MANUFACTURED FROM MY 1992 THROUGH 2003 WITH A TEXAS INSTRUMENTS SCDS.NHTSA WILL CONTINUE TO MONITOR THE RECALLED VEHICLES TO ENSURE REMEDIES INSTALLED BY FORD TOMITIGATE THE POTENTIAL FOR SCDS RELATED FIRES ARE EFFECTIVE.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES.SEE ATTACHED CLOSING REPORT FOR FURTHER DETAILS.

ENGINE COMPARTMENT FIRES

PE08035 · opened May 13, 2008 · closed Sep 17, 2008
Summary

ODI HAS RECEIVED 134 CONSUMER COMPLAINTS, 285 MANUFACTURER COMPLAINTS, AND 137 MANUFACTURER WARRANTY CLAIMS ALLEGING INCIDENTS OF ENGINE COMPARTMENT FIRE IN MODEL YEAR (MY) 1995 THRU 2003 FORD WINDSTAR VEHICLES.TWO OF THE ODI COMPLAINTS ALLEGE THE FIRES CAUSED STRUCTURAL DAMAGE TO THE COMPLAINANT'S HOME.OF THE 134 ODI COMPLAINTS, 36 ALLEGE THE FIRE OCCURRED WHILE THE VEHICLE WAS PARKED, 72 ALLEGE THE FIRE OCCURRED WHILE THE VEHICLE WAS RUNNING AND 26 OF THE COMPLAINTS DO NOT SPECIFY IF THE VEHICLE WAS RUNNING OR NOT.FURTHER REVIEW OF THE ODI COMPLAINTS SHOWS THAT 72 ALLEGE THAT THE SPEED CONTROL DEACTIVATION SWITCH (SCDS) CAUSED THE FIRE AND 10 ALLEGE THAT THE SCDS LEAKED BRAKE FLUID ON TO THE ABS MODULE RESULTING IN THE FIRE.THERE WERE 52 THAT DID NOT IDENTIFY A CAUSE OR THAT IDENTIFIED MISCELLANEOUS OTHER CAUSES.ODI HAS ALSO RECEIVED 89 COMPLAINTS ( NOT COUNTED IN THIS RESUME) ALLEGING THAT THE SCDS DEVELOPED A BRAKE FLUID LEAK.THIRTEEN OF THESE COMPLAINTS SAY THAT THE LEAK AT THE SCDS RESULTED IN BRAKED FLUID REACHING THE ABS MODULE.THIS PE HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA) TO FURTHER EVALUATE THE CAUSE OF THE FIRES AND ASSESS THE SCOPE, FREQUENCY, AND SAFETY CONSEQUENCES OF THE ALLEGED DEFECT.

FRONT SEAT BELT BUCKLE ASSEMBLY

EA05004 · opened Feb 17, 2005 · closed Jul 6, 2005
Summary

DURING THE INITIAL RECALL CAMPAIGN IN 2001, THE SUBJECT VEHICLES WERE INSPECTED BY FORD DEALERSHIPS USING A TEST TOOL THAT WOULD DETECT A DEFECTIVE FRONT SEAT OUTBOARD SEAT BELT BUCKLE ASSEMBLY.APPROXIMATELY ONE MILLION VEHICLES PASSED THE INSPECTION TEST FOR ONE OR BOTH FRONT BUCKLES.SUBSEQUENT TO THE RECALL SERVICE ACTION, ODI RECEIVED 15 CONSUMER REPORTS ALLEGING THAT A PASSED INSPECTION BUCKLE SUBSEQUENTLY FAILED TO LATCH OR INADVERTENTLY UNLATCHED DURING USE.IN ADDITION, FORD HAS IDENTIFIED 543 OWNER AND FIELD REPORTS ALLEGING BUCKLE FAILURE SUBSEQUENT TO PASSING THE INSPECTION TEST.FORD TESTED AND EXAMINED OVER 100 WARRANTY-RETURNED BUCKLES AND FOUND THAT 44% OF THE BUCKLES HAD NO PROBLEM OR A CONDITION NOT RELATED TO THE RECALL INSPECTION (NON-LATCH RELATED BUCKLE DAMAGE OR FOREIGN CONTAMINATION).WARRANTY CLAIMS WERE HIGHEST DURING THE 18-MONTH PERIOD AFTER THE START OF THE RECALL (JULY 2001) AND HAVE BEEN DECLINING DURING THE PAST 24 MONTHS.OVER THE PAST 12 MONTHS, FORD HAS RECEIVED APPROXIMATELY 12 WARRANTY CLAIMS PER MONTH OUT OF A VEHICLE POPULATION OF ABOUT ONE MILLION.COMPLAINTS COUNTS ARE ALSO DECREASING.DURING THE PAST SEVEN MONTHS, ODI HAS RECEIVED ONLY TWO COMPLAINTS. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGEN…

FRONT SEAT BELT BUCKLE ASSEMBLY

RQ04011 · opened Oct 22, 2004 · closed Feb 17, 2005
Summary

UNDER RECALL CAMPAIGN (01V227), FORD RECALLED APPROXIMATELY 1.3 MILLION VEHICLES TO INSPECT AND IF NECESSARY REPLACE THE FRONT DRIVER AND/OR PASSENGER SEAT BELT BUCKLE.APPROXIMATELY 1.1 MILLION OWNERS RESPONDED BY TAKING THEIR VEHICLES TO A DEALER FOR INSPECTION OF THE BUCKLE USING A SPECIALIZED BUCKLE TEST TOOL.FORD REPORTED THAT 829,927 VEHICLES HAD BOTH BUCKLES PASS THE TOOL TEST AND ANOTHER 167,336 VEHICLES HAD ONE BUCKLE PASS.ODI AND FORD RECEIVED COMPLAINTS ALLEGING SEAT BELT BUCKLE FAILURE SHORTLY AFTER PASSING THE ORIGINAL RECALL INSPECTION SERVICE.COMPLAINANTS ALLEGED THAT THE BUCKLE FAILED BY EITHER NOT LATCHING OR FALSE-LATCHING (PARTIAL ENGAGEMENT OF THE LATCH TO THE LATCH PLATE).A FALSE-LATCHED BUCKLE MAY RELEASE WITH MINOR MOVEMENT OR IMPACT AGAINST THE BUCKLE HOUSING INCLUDING INADVERTENT RELEASE WHILE THE VEHICLE IS IN MOTION.ODI IS UPGRADING THIS RECALL QUERY TO AN ENGINEERING ANALYSIS (EA05-004) TO FURTHER ANALYZE THE FIELD PERFORMANCE OF THOSE VEHICLES THAT FORD DEALERS PASSED (ONE OR BOTH BUCKLES) USING FORD'S INSPECTION TEST (997,263 VEHICLES).

POWER SLIDING DOOR OPENING

PE04022 · opened Mar 3, 2004 · closed Jul 1, 2004
Summary

THE SUBJECT VEHICLES ARE EQUIPPED WITH SINGLE OR DUAL POWER SLIDING DOORS (PSD).APPROXIMATELY 111,000 VEHICLES HAVE DUAL POWER SLIDING DOORS.THE PSD IS OPENED BY ANY OF 5 METHODS, THE INSIDE OR OUTSIDE MANUAL DOOR HANDLE, THE KEY FOB, THE OVERHEAD CONSOLE SWITCH AND THE B-PILLAR SWITCH.THE DOOR MAY BE OPENED ONLY UNDER THESE CONDITIONS: IGNITION KEY IS IN OFF/ACCESSORIES/ON/START POSITION, GEAR SELECTOR IN PARK, VEHICLE SPEED LESS THAN 6 MPH, AND DOOR UNLOCKED.THE PSD LATCH IS LOCATED AT THE REAR OF THE DOOR AND HAS A SECONDARY AND PRIMARY LATCH POSITION.FULL AND PROPER CLOSURE ENGAGES BOTH THE SECONDARY AND PRIMARY LATCH.WITH THE IGNITION IN THE ON POSITION, AS THE GEAR SELECTOR IS MOVED OUT OF PARK THE DOOR AUTOMATICALLY LOCKS AND THAT ACTION MECHANICALLY ISOLATES THE LATCH, SECONDARY AND PRIMARY, FROM ALL LATCH RELEASE CONNECTIONS.IN ADDITION TO THE REPORTS ALLEGING DOOR OPENING WHILE DRIVING, FORD HAS RECEIVED APPROXIMATELY 5,700 REPORTS THAT ALLEGE THE DOOR DOES NOT CLOSE PROPERLY OR POPS OPEN WITH NO MENTION OF WHILE DRIVING.FORD'S INVESTIGATION INTO THESE REPORT INCLUDED OWNER INTERVIEWS, VEHICLE BY-BACKS AND TESTING OF CONSUMER VEHICLES.IT FOUND THAT ALLEGATIONS OF DOOR OPENING WHILE DRIVING WERE IN FACT REPORTS OF DOORS NOT BEING PROPERLY CLOSED INITIALLY AND SUBSEQUENTLY OPENING TO THE SECONDARY LATCH POSITION AS A RESULT OF VEHICLE VIBRATIONS OR DRIVING MANEUVERS.FORD'S TESTING OF CONSUMER VEHICLES DID NOT RESULT IN ANY RECURRENCE OF PSD OPENING WHILE BEING DRIVEN.…

2001 vs. other Ford Windstar years

Owner complaints by model year; the darker bar is the 2001. Click a bar to switch year.

Questions

Does the 2001 Ford Windstar have recalls?

Yes — NHTSA lists 15 recall campaigns covering the 2001 Ford Windstar, the latest from Sep 29, 2015 (suspension). A recall applies to specific vehicles: enter your VIN at nhtsa.gov/recalls to see whether yours is affected and still open.

What are the most common problems with the 2001 Ford Windstar?

Owner complaints filed with NHTSA most often mention service brakes (540), suspension (416), structure (293). Complaints are consumer reports and are not verified by NHTSA.