2007 Ford Freestar recalls and problems

Ford is conducting a safety recall to repair the third-row seat's latch mechanisms in approximately 196,667 model year (MY) 2004 through 2007 Ford Freestar and Mercury Monterey vehicles (see NHTSA recall 13V-081 for more details).The recall covers vehicles originally sold, or currently registered, in the salt belt states or high corrosion areas of the United States: Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, and Wisconsin.Approximately 100,000 remaining MY 2004-2007 Freestar and Monterey vehicles--those vehicles that were not originally sold, or are not currently registered, in salt belt states--are not included in the recall action. Although these vehicles are the same as the ones described above, they experience significantly lower failure rates because of reduced road salt exposure.ODI is currently aware of only one complaint on vehicle outside of the recall scope.ODI will monitor complaints and take further action if warranted by the circumstances.For owners of vehicles that are outside of the recall scope but exhibit the defect condition, owners (and affected Ford dealers) can contact Ford to request the recall repair.This Engineering Analysis is closed.See attached report and associated recall file for additional information.The ODI reports cited above can be reviewed online at http:/…

The subject vehicles suffered from a design issue whereby water could run down onto the cowling under the hood and located in the area of the windshield wipers and then drip onto a computer module, the Powertrain Control Module (PCM), which could be manifested in a variety of symptoms depending on which part of the circuit board became wet or which of the connector pins shorted out.In addition to causing an engine to stall, which may or may not then restart, the water intrusion could also cause the transmission to shift poorly, the vehicle to have erratic power, a malfunction indicator light to come on, or result in an inability to start the vehicle, an inability to shift the vehicle into either forward or reverse. Also the problem could cause a higher than normal idle RPM in Park, or for the radio to malfunction, or the interior lights to stay on.During this investigation ODI was concerned with the effect of the engine stalling or a drastic and sudden loss of power either of which may create a safety risk.In reviewing the actual number of these types of incidents, collectively referred to here as engine stalls, the number was found to be below what would be considered a defect trend.For example, the number of engine stalls identified in Ford's warranty claims for the model year (MY) 2004 subject vehicles, the MY with the most failures, was 200 out of population of 125,865, for a failure rate of 0.16%.The one crash recorded by a complainant to NHTSA, VOQ 10311522, alleged tha…

ON OCTOBER 14, 2008, ODI OPENED PE08-060 TO INVESTIGATE ALLEGATIONS OF CRACKED AND LEAKING SNAP-IN TIRE VALVES IN MODEL YEAR (MY) 2007 VEHICLES MANUFACTURED BY FORD MOTOR COMPANY.THE VALVES WERE SUPPLIED TO FORD BY TOPSEAL AUTO-PARTS, A SUBSIDIARY OF THE SHANGHAI BAOLONG AUTOMOTIVE CORPORATION IN CHINA.VALVES MADE BY TOPSEAL FOR AFTERMARKET SALE WERE THE SUBJECT OF TWO RECENT SAFETY RECALLS BY TECH INTERNATIONAL (08T-018) AND DILL AIR CONTROLS (08T-028), THE LATTER OF WHICH WAS INVESTIGATED BY ODI IN PE08-036 AND EA08-022.THE DEFECT CONDITIONS ADDRESSED BY THE AFTERMARKET TIRE VALVE RECALLS BOTH INVOLVED INADEQUATE RESISTANCE TO OZONE CRACKING DUE TO ISSUES WITH THE SUPPLY OF ANTI-OZONANT CHEMICALS TO TOPSEAL FOR A PERIOD FROM JULY TO MID-NOVEMBER 2006.THE AFTERMARKET VALVES WERE COMPOUNDED WITH A BLEND OF EPDM AND NATURAL RUBBER, USING A RELATIVELY LOW PERCENTAGE OF EPDM (EPDM PROVIDES INHERENT RESISTANCE TO OZONE CRACKING).HENCE, THE NEED FOR ANTI-OZONANT CHEMICALS AND THE PROBLEMS WITH CRACKING WHEN THOSE CHEMICALS WERE MISSING OR OUT OF SPECIFICATION IN SOME LOTS OF VALVES.BOTH RECALL CAMPAIGNS INVOLVED INSPECTION PROGRAMS TO IDENTIFY AND REPLACE VALVES WITH VISIBLE SURFACE CRACKING.ALTHOUGH THE TOPSEAL VALVES SUPPLIED TO FORD ALSO APPEAR TO HAVE BEEN AFFECTED BY THE ANTI-OZONANT SUPPLY ISSUES IN MID TO LATE-2006, FORD INDICATED THAT ITS VALVES WERE MADE AT A DIFFERENT TOPSEAL PRODUCTION LINE AND WERE COMPOUNDED WITH A HIGHER PERCENTAGE OF EPDM RUBBER TO MEET MORE STRINGE…