2006 Chevrolet Corvette Z06 recalls and problems

On May 14, 2014, General Motors (GM) submitted a Part 573 defect information report initiating NHTSA Safety Recall 14V-251 to remedy the subject vehicles.GM will remedy a defect condition in the underhood bussed electrical center (UBEC) by modifying the vehicle's electrical harnessing.GM also announced a customer satisfaction bulletin to address this issue on model year (MY) 2008-2013 Chevrolet Corvettes.Both programs will be conducted free of charge.According to GM, when the engine heats up and cools down (from normal use), the plastic material in the UBEC housing expands at a different rate than an electrical conductor routed within it.The difference in expansion rates results in bending of the conductor, a control circuit for the low beam headlights.After multiple thermal cycles, often taking several years of use, the conductor fractures resulting in an open circuit.When this occurs the low-beam headlights will not illuminate.After the engine is turned off and the UBEC cools, the conductor may temporarily reconnect and restore low-beam function, although subsequent failures will occur.This condition does not affect high-beam headlights, marker lamps, turn signals or fog lamps.Simultaneous loss of low-beam headlights could reduce the driver's visibility, increasing the risk of a crash. The ODI report counts noted above, involving the loss of low beam headlights, represents those received at the time of GM's recall filing; however NHTSA has since received additional complain…

The Office of Defects Investigation (ODI) opened this investigation based on 30 reports from consumers alleging that, after driving for a short time (5 to 30 minutes), both low beam headlights stopped working simultaneously and without warning. The low beam headlights remained inoperative for the remainder of the drive cycle, however no other lighting is affected.General Motors (GM) provided information in response to ODI's information request letter explaining that the loss of headlights is caused by a fractured low beam circuit wire in the underhood bussed electrical center (UBEC), a device that is similar to a fuse box. The UBEC is located in a high heat area near the engine, and the low beam circuit wire routing within the UBEC makes it susceptible to cyclical stress caused by thermal expansion.The investigation covers model years 2005-2007 Corvettes however ODI also has received four VOQs alleging the same condition in model year 2008 Corvettes. ODI is upgrading the investigation to an Engineering Analysis to further examine the consequences, frequency and scope of this problem. The ODI reports cited above can be reviewed at http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers.For MY 2005-2007: 10400308, 10415603, 10415867, 10416531, 10421639, 10424391, 10424543, 10445971, 10451733, 10454919, 10460674, 10460750, 10463546, 10466342, 10466857, 10468128, 10469057, 10470616, 10471595, 10474350, 10474368, 10475257, 10486597, 10491…

On April 26, 2010, at NHTSA's request following this investigation, General Motors submitted a Defect Information Report to NHTSA to correct a defect associated with the Vehicle Stability Control (VSC) system in approximately 40,000 Model Year (MY) 2005 and 2006 Chevrolet Corvette vehicles (NHTSA Recall No. 10V-172).According to the report, these vehicles may have a problem with the Steering Wheel Position Sensor (SWPS) connector created by a fretting condition in the connector (small movement of the pins back and forth creating a residue build up) which could change the electrical resistance and corrupt the information signal to the VSC computer.The VSC system uses the information from the SWPS to calculate the driver's intended vehicle direction; this information is cross referenced to sensors that tell the system which direction the vehicle is actually going and the system will, if it determines a variance indicating the vehicle is in a over-steer or under-steer condition, reduce throttle control and apply braking to make a correction in vehicle direction towards what the system believes is the driver's intended path.GM dealers will inspect the SWPS connector of recalled vehicles and, if necessary, install a terminal position assurance clip to the connector.GM has advised NHTSA that its position is that the inappropriate activations of the VSC system do not present an unreasonable risk to safety because GM believes that the activations are low in occurrence, a rare set of …

ON SEPTEMBER 17, 2008, ODI OPENED PRELIMINARY EVALUATION PE08-056 TO INVESTIGATE ALLEGATIONS OF INAPPROPRIATE ACTIVATION OF THE ELECTRONIC STABILITY CONTROL (ESC) SYSTEM IN MODEL YEAR (MY) 2005 AND 2006 CHEVROLET CORVETTE VEHICLES.SOME REPORTS RECEIVED BY ODI AND SOME REPORTS TO GENERAL MOTORS (GM) CONTAINED IN GM'S RESPONSE TO PE08-056 ALLEGE THAT THE ESC SYSTEM MALFUNCTIONED CAUSING A SUDDEN AND INAPPROPRIATE BRAKING ACTION WITHOUT ILLUMINATION OF THE BRAKE LIGHTS AND CAUSING THE VEHICLE TO SWERVE LEFT OR RIGHT UNEXPECTEDLY. GM ISSUED A TECHNICAL SERVICE BULLETIN IN JANUARY 2006, LATER REVISED IN OCTOBER 2007 (BULLETIN NO. 06-02-35-002B) CONCERNING ESC PROBLEMS IN MY 2005 AND 2006 CHEVROLET CORVETTE VEHICLES WITH THE TELESCOPING STEERING WHEEL OPTION.THE BULLETIN WAS INTENDED TO CORRECT A FRETTING CORROSION PROBLEM WITH THE STEERING WHEEL POSITION SENSOR CONNECTOR C202. AN ENGINEERING ANALYSIS HAS BEEN OPENED (EA09-002) TO CONTINUE TO ASSES THE SCOPE, FREQUENCY, AND SAFETY-RELATED CONSEQUENCES OF THE ALLEGED DEFECT.